AT T CL80111 User Manual

User’s manual  
CL80111  
DECT 6.0 expansion handset  
for use with AT&T models  
CL83101/CL83201/CL83301/  
CL83351/CL83401/CL83451  
Parts checklist  
Your telephone package contains the following items. Save your  
sales receipt and original packaging in the event warranty service  
is necessary.  
User’s manual  
CL80111  
DECT 6.0 expansion handset  
for use with AT&T models  
CL83101/CL83201/CL83301/  
CL83351/CL83401/CL83451  
User’s manual  
Cordless handset  
Charger for cordless  
handset with power  
adapter installed  
Battery  
Battery for  
compartment  
cover  
cordless handset  
User’s manual  
CL80111  
DECT 6.0 expansion handset  
for use with AT&T models  
CL83101/CL83201/CL83301/  
CL83351/CL83401/CL83451  
Table of contents  
Getting started  
Installation  
You must install and  
charge the battery before  
using the telephone.  
See pages 6-7  
STOP!  
for easy instructions.  
Your product may be shipped with a protective sticker covering the  
handset display - remove it before use.  
For customer service or product information, visit our website at  
www.telephones.att.com or call 1 (800) 222-3111.  
In Canada, dial 1 (866) 288-4268.  
Avoid placing the telephone base too close to:  
• Communication devices such as television sets, VCRs, or other  
cordless telephones.  
• Excessive heat sources.  
• Noise sources such as a window with traffic outside, motors,  
microwave ovens, refrigerators, or fluorescent lighting.  
• Excessive dust sources such as a workshop or garage.  
• Excessive moisture.  
• Extremely low temperature.  
• Mechanical vibration or shock such as on top of a washing  
machine or workbench.  
1
 
Getting started  
Quick reference guide - handset  
CHARGE indicator  
On when the handset is charging in the  
telephone base or charger.  
MUTE/DELETE  
During a call, press to mute the microphone.  
When the handset is ringing, press to mute the  
ringer temporarily.  
While reviewing the caller ID history, the  
directory or the redial memory, press to delete  
an individual entry.  
While predialing, press to delete digits.  
During message playback, press to delete the  
playing message.  
PHONE/FLASH  
Press to make or answer a call.  
During a call, press to answer an incoming call  
when you receive a call waiting alert.  
During message playback, press to call back the  
caller if caller’s number is available.  
1
While reviewing a caller ID log entry, press  
repeatedly to add or remove 1 in front of the  
telephone number before dialing or saving it in  
the directory.  
TONE  
Press to switch to tone dialing temporarily  
during a call if you have pulse service.  
/SPEA�ER  
Press to make or answer a call using the  
speakerphone.  
Press to switch between the speakerphone and  
the handset.  
REDIAL/PAUSE  
Press repeatedly to view the last 10 numbers  
dialed.  
While entering numbers, press and hold to insert  
a dialing pause.  
2
 
Getting started  
Quick reference guide - handset  
pDIR/VOLUME  
Press pDIR to show directory entries when  
the handset is not in use.  
Press to scroll up while in menus.  
While entering names or numbers, press to  
move the cursor to the right.  
Press to increase the listening volume during a  
call or message playback.  
MENU/SELECT  
When the handset is not in use, press to show  
the menu.  
While in the menu, press to select an item or  
save an entry or setting.  
OFF/CANCEL  
During a call, press to hang up.  
While in a menu, press to cancel an operation,  
back up to the previous menu, or exit the  
menu display, or press and hold this button to  
exit to idle mode.  
When the handset is ringing, press to mute the  
ringer temporarily.  
Press and hold while the telephone is not in  
use to erase the missed call indicator.  
qCID/VOLUME  
Press qCID to show caller ID history when the  
handset is not in use.  
Press to scroll down while in menus.  
While entering names or numbers, press to  
move the cursor to the left.  
Press to decrease the listening volume during  
a call or message playback.  
#(pound key)  
Press repeatedly to display other dialing  
options when reviewing a caller ID log entry.  
EQ  
During an outside call, intercom call, message  
or announcement playback, press to change  
the audio quality to best suit your hearing.  
3
Getting started  
Quick reference guide - handset  
PUSH TO TAL�  
Press to initiate a one-to-one or one-to-group broadcast.  
Press and hold to broadcast to a group of system devices.  
Main menu  
Main menu  
• Play messages  
• Answering sys  
• Directory  
The > symbol highlights  
a menu item.  
• Caller ID log  
• Intercom  
• Ringers  
>Play messages  
Answering sys  
• Set date/time  
• Settings  
p
q
• Website  
Using menus:  
• Press MENU/SELECT to show the menu.  
• Press qCID or pDIR to scroll through menu items.  
• Press MENU/SELECT to confirm or save changes to a highlighted  
menu item.  
• Press OFF/CANCEL to cancel an operation, back up to the  
previous menu, or exit the menu display.  
For complete instructions, refer to the user’s manual provided with  
your CL83101/CL83201/CL83301/CL83351/CL83401/CL83451  
telephone system.  
If you are unable to find your user’s manual, go to  
www.telephones.att.com to read and/or download the manual.  
4
Getting started  
Charger installation  
Install the charger as shown below.  
Plug the power adapter into an  
electrical outlet not controlled by  
a wall switch.  
IMPORTANT INFORMATION  
Use only the power adapter supplied with this product. To order a replacement  
power adapter, visit our website at www.telephones.att.com or call  
1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.  
The power adapter is intended to be correctly oriented in a vertical or floor  
mount position. The prongs are not designed to hold the plug in place if it is  
plugged into a ceiling, under-the-table or cabinet outlet.  
5
 
Getting started  
Battery installation and charging  
Install the battery as shown on page 7. Once you have installed  
the battery, the screen indicates the battery status (see the table  
below). If necessary, place the handset in the telephone base or  
charger to charge the battery. For best performance, keep the  
handset in the telephone base or charger when not in use. The  
battery is fully charged after 10 hours of continuous charging. See  
the table on page 28 for battery operating times.  
If the screen shows Place in charger and flashes, you need to  
charge the handset without interruption for at least 30 minutes to  
give the handset enough charge to use the telephone for a short  
time. The following table summarizes the battery charge indicators  
and actions to take.  
Battery indicators  
Battery status  
Action  
The screen is blank, Battery has no or  
Charge without interruption  
(at least 30 minutes).  
or shows Place in  
charger and  
(flashing).  
very little charge. The  
handset cannot be used.  
The screen shows  
Low battery and  
(flashing).  
Battery has enough  
charge to be used for a (at least 30 minutes).  
short time.  
Charge without interruption  
The screen shows  
HANDSET X.  
Battery is charged.  
To keep the battery charged,  
place it in the telephone base or  
charger when not in use.  
NOTE: If you are on a phone call in low battery mode, you hear four short  
beeps every minute.  
6
 
Getting started  
Battery installation and charging  
Step 1  
Step 2  
Plug the battery  
Align the cover  
flat against  
the battery  
compartment,  
then slide it  
upwards until it  
clicks into place.  
connector securely  
into the socket inside  
the handset battery  
compartment, matching  
the color-coded label.  
Insert the supplied  
battery with the label  
THIS SIDE UP facing up  
as indicated.  
CHARGE light  
Step 3  
Charge the handset by placing it face forward in the  
telephone base or charger. The CHARGE light on the  
top of the handset is on during charging.  
After you install your telephone or power returns following a power  
outage, the handset will prompt you to set the date and time. For  
instructions, see Set date/time in the telephone system user’s  
manual for details. To skip setting the date and time, press  
OFF/CANCEL.  
IMPORTANT INFORMATION  
• Use only the supplied rechargeable battery or replacement battery  
(wmwodwel.BtTe1l6e6p34h2o).nToesor.daetrt,.vcisoitmouorrwceabllsi1te(a8t 00) 222-3111.  
In Canada, dial 1 (866) 288-4268.  
• If you do not use the handset for a long time, disconnect and remove  
the battery to prevent possible leakage.  
7
Registration and deregistration  
Adding and registering handsets  
Before using a new CL80111 handset, you must register it with the  
AT&T CL83101/CL83201/CL83301/CL83351/CL83401/CL83451  
telephone system (purchased separately). The telephone system  
can support up to 12 handsets.  
The handsets provided with your telephone system are already  
registered as HANDSET 1 and so forth. Additional handsets  
registered to the telephone system are assigned in sequential  
order they are registered (up to HANDSET 12).  
You must register each handset separately. When first purchased,  
all expansion handsets show Put HS on BASE to register.  
Register a handset to your telephone base  
1. Make sure the handset is out of the telephone base  
Put HS on BASE  
or charger and shows Put HS on BASE to register  
to register  
before you begin registration.  
2. Put the handset you wish to register on the  
telephone base cradle.  
3. Both the handset and the telephone base show  
Registering...  
Registering... Please wait and the IN USE light  
Please wait  
on the telephone base turns on. Then  
HANDSET X Registered appears on both  
the handset and the telephone base screens  
(HANDSET represents the handset name, X  
represents the handset number). Both the  
HANDSET X  
Registered  
handset and the telephone base beep and the  
IN USE light turns off. The handset is now  
registered with the telephone base.  
If registration fails, the system will  
automatically try to register again. If  
registration fails after the third try,  
Registration failed appears on both  
screens. Then the handset shows  
Put HS on BASE to register and the  
telephone base returns to idle mode.  
This may take up to five minutes to  
occur. Please start again from Step 1 above.  
NOTE: You cannot register a handset if any other system handset is in use.  
8
 
Registration and deregistration  
Deregistering handsets  
You may need to deregister your handsets if:  
• You have 12 registered handsets and need to replace a handset.  
-OR-  
• You wish to change the designated handset number of your  
registered handsets.  
You must first deregister ALL handsets, and then register each  
handset you wish to use again, one at a time.  
Please read carefully through all the instructions on this page  
before beginning the deregistration process.  
Deregister all handsets from your telephone base  
1. Make sure that all handsets are out of the telephone base and  
chargers before you begin deregistration.  
2. Press and hold /HANDSET LOCATOR on  
the telephone base for about 10 seconds  
(until the IN USE light starts to flash),  
then the telephone base screen shows  
Deregister all devices?  
Release /HANDSET LOCATOR.  
3. Immediately press /HANDSET LOCATOR  
while the IN USE light is still flashing. (If  
the light stops flashing, start again with Step 1 above.)  
4. It takes up to 10 seconds to complete the deregistration  
process. Wait for the cordless handset screen to display Put HS  
on BASE to register before registering the handset again.  
5. To register the handset(s) to the telephone base again, follow  
the registration instructions on the previous page.  
After you deregister the handset(s), the date and time need to be set.  
NOTES:  
If the deregistration process fails, you may need to reset the system and try  
again. To reset, unplug the power from the telephone base and plug it back in.  
You cannot deregister the handsets if any other system handset is in use.  
Even if the battery is depleted, you can still deregister the handsets by following  
the steps above. After the handset is charged for at least 10 minutes, the screen  
shows Put HS on BASE to register.  
9
 
Appendix  
Troubleshooting  
If you have difficulty with your phone, please try the suggestions  
below. For Customer Service, visit our website at  
www.telephones.att.com or call 1 (800) 222-3111.  
In Canada, dial 1 (866) 288-4268.  
The handset registration is unsuccessful.  
• Follow the handset registration instructions to register the  
handset again (see Adding and registering handsets on page 8).  
My telephone doesn’t work at all.  
• Make sure the power cord is securely plugged in.  
• Make sure you plug the battery connector securely into the  
cordless handset.  
• Make sure you plug the telephone line cord securely and firmly  
into the telephone base and the telephone wall jack.  
• Charge the battery in the cordless handset for at least 10 hours.  
For optimum daily performance, return the cordless handset to  
the charger when not in use.  
• If the battery is depleted, it may take approximately 30 minutes  
to charge the handset before it shows Low battery. See page 6  
for details.  
• Reset the telephone base. Unplug the electrical power. Wait for  
approximately 15 seconds, then plug it back in. Allow up to one  
minute for the cordless handset and telephone base to reset.  
• You may need to purchase a new battery. Refer to Battery  
installation and charging in this user’s manual on pages 6-7.  
I cannot get a dial tone.  
• Try all the suggestions above.  
• Move the cordless handset closer to the telephone base. You  
may have moved out of range.  
10  
 
Appendix  
Troubleshooting  
• If the previous suggestions do not work, disconnect the  
telephone base from the telephone jack and connect the jack to  
a different phone. If there is no dial tone on that phone either,  
the problem is in your wiring or telephone service. Contact your  
telephone service provider.  
• Your line cord may be defective. Try installing a new line cord.  
I cannot dial out.  
• Try all the suggestions above.  
• Make sure you have a dial tone before dialing. The cordless  
handset may take a second or two to find the telephone base  
and produce a dial tone. This is normal. Wait an extra second  
before dialing.  
• Eliminate any background noise. Noise from a television, radio or  
other appliances may cause the phone to not dial out properly.  
If you cannot eliminate the background noise, try muting the  
cordless handset before dialing, or dialing from another room  
with less background noise.  
• If other phones in your home are having the same problem,  
contact your telephone service provider (charges may apply).  
My cordless handset isn’t performing normally.  
• Make sure you plug the power cord securely into the telephone  
base. Plug the power adapter into a different, working electrical  
outlet without a wall switch.  
• Move the cordless handset closer to the telephone base. You  
may have moved out of range.  
• Reset the telephone base. Unplug the electrical power. Wait for  
15 seconds then plug it back in. Allow up to one minute for the  
cordless handset and telephone base to reset.  
• Other electronic products such as HAM radios and other DECT  
phones can cause interference with your cordless phone. Try  
installing your phone as far away as possible from these types  
of electronic devices.  
11  
Appendix  
Troubleshooting  
Out of range OR No pwr at base appears on my cordless  
handset.  
• Ensure you plug the telephone base in properly and the power  
is on.  
• Place the cordless handset in the telephone base for one  
minute to allow the cordless handset and base to synchronize.  
• Move the cordless handset closer to the telephone base. You  
may have moved out of range.  
• Reset the telephone base. Unplug the electrical power. Wait for  
15 seconds then plug it back in. Allow up to one minute for the  
cordless handset and telephone base to reset.  
• Other electronic products such as HAM radios and other DECT  
phones can cause interference with your cordless phone. Try  
installing your phone as far away as possible from these types  
of electronic devices.  
The batteries do not hold a charge.  
• If the cordless handset is in the telephone base or charger and  
the charge light is not on, refer to The charge light is off or  
blinking (page 17).  
• Charge the battery in the cordless handset for at least 10 hours.  
For optimum daily performance, return the cordless handset to  
the telephone base or charger when not in use.  
• If the battery is depleted, it may take approximately 30 minutes  
to charge the handset before it shows Low battery. Refer to the  
table on page 6 for details.  
• You may need to purchase a new battery. Refer to Battery  
installation and charging in this user’s manual on pages 6-7.  
I hear other calls while using my phone.  
• Disconnect the telephone base from the telephone jack, and  
plug in a different telephone. If you still hear other calls, call  
your telephone service provider.  
12  
Appendix  
Troubleshooting  
I get noise, static, or weak signals even when I’m near the  
telephone base.  
• If you subscribe to high-speed Internet service (DSL - digital  
subscriber line) through your telephone line, you must install a  
DSL filter between the telephone line cord and the telephone  
wall jack. The filter prevents noise and caller ID problems as  
a result of DSL interference. Please contact your DSL service  
provider for more information about DSL filters.  
• You may be able to improve the performance of your cordless  
phone by installing your telephone base as far as possible from  
any other existing cordless telephone system that may already  
be installed.  
• Other electronic products such as HAM radios and other DECT  
phones can cause interference with your cordless phone. Try  
installing your phone as far away as possible from these types  
of electronic devices.  
• Do not install this phone near a microwave oven or on the same  
electrical outlet. You may experience decreased performance  
while the microwave oven is operating.  
• If you plug your phone in with a modem or a surge protector,  
plug the phone (or modem/surge protector) into a different  
location. If this does not solve the problem, relocate your phone  
or modem farther apart from one another, or use a different  
surge protector.  
• Move your phone to a higher location. The phone may have  
better reception in a high area.  
• If other phones in your home are having the same problem,  
contact your telephone service provider (charges may apply).  
I experience poor sound quality when using the speakerphone.  
• For increased sound quality while using the speakerphone, place  
the handset on a flat surface with the dialing keys facing up.  
13  
Appendix  
Troubleshooting  
My cordless handset does not ring when I receive a call.  
• Make sure that the ringer is not off. Refer to Ringer volume in  
the CL83101/CL83201/CL83301/CL83351/CL83401/CL83451  
user’s manual provided with your telephone.  
• Make sure you plug the telephone line cord securely into the  
telephone base and telephone jack. Make sure you plug in the  
power cord securely.  
• The cordless handset may be too far from the telephone base.  
• Charge the battery in the cordless handset for at least 10 hours.  
For optimum daily performance, return the cordless handset to  
the telephone base or charger when not in use.  
• You may have too many extension phones on your telephone  
line to allow all of them to ring simultaneously. Try unplugging  
some of the other phones.  
• The layout of your home or office may be limiting the operating  
range. Try moving the telephone base to another location,  
preferably on an upper floor.  
• If other phones in your home are having the same problem,  
contact your telephone service provider (charges may apply).  
• Test a working phone at the phone jack. If another phone has  
the same problem, contact your telephone service provider  
(charges may apply).  
• Other electronic products such as HAM radios and other DECT  
phones can cause interference with your cordless phone. Try  
installing your phone as far away as possible from these types  
of electronic devices.  
• Remove the battery. Replace it and place the cordless handset  
into the telephone base. Allow up to one minute for the handset  
to reestablish its connection with the telephone base.  
• Your line cord may be defective. Try installing a new line cord.  
14  
Appendix  
Troubleshooting  
My calls cut in and out while I’m using my cordless handset.  
• Other electronic products such as HAM radios and other DECT  
phones can cause interference with your cordless phone. Try  
installing your phone as far away as possible from these types  
of electronic devices.  
• Do not install this phone near a microwave oven or on the same  
electrical outlet. You may experience decreased performance  
while the microwave oven is operating.  
• If you plug your phone in with a modem or surge protector, try  
plugging the phone (or modem/surge protector) into a different  
location. If this does not solve the problem, relocate your phone  
or modem farther apart from one another, or use a different  
surge protector.  
• Move your telephone base to a higher location. The phone may  
have better reception when installed in a high area.  
• If other phones in your home are having the same problem,  
contact your telephone service provider (charges may apply).  
My caller ID isn’t working.  
• Caller ID is a subscription service. You must subscribe to this  
service from your telephone service provider for this feature to  
work on your phone.  
• The caller must be calling from an area that supports caller ID.  
• Both your and your caller’s telephone service providers must  
use caller ID compatible equipment.  
• If you subscribe to high-speed Internet service (DSL - digital  
subscriber line) through your telephone line, you must install a  
DSL filter between the telephone line cord and the telephone  
wall jack. The filter prevents noise and caller ID problems  
resulting from DSL interference. Contact your DSL service  
provider for more information about DSL filters.  
15  
Appendix  
Troubleshooting  
System does not receive caller ID when on a call.  
• Make sure you subscribe to caller ID with call waiting features  
from your telephone service provider. Caller ID features work  
only if both you and the caller are in areas offering caller  
ID service, and if both telephone service providers use  
compatible equipment.  
I subscribe to a nontraditional telephone service that uses  
my computer to establish connections, and my telephone  
doesn’t work.  
• Make sure your computer is powered on.  
• Make sure your Internet connection is working properly.  
• Make sure that the software is installed and running for your  
nontraditional telephone service.  
• Make sure to plug your USB telephone adapter into a dedicated  
USB port on your computer. Do not plug it into a multiple port  
USB hub (USB splitter) that is not powered.  
• In a few rare instances, the USB port on your computer may  
not have enough power. In these instances, try using a USB hub  
with its own external power supply.  
• If you are using a firewall, it may prevent access to your  
nontraditional telephone service provider. Contact your service  
provider for more information.  
16  
Appendix  
Troubleshooting  
The charge light is off or blinking.  
• Make sure you plug the power and line cords in correctly  
and securely.  
• Unplug the electrical power. Wait for 15 seconds, then plug it  
back in. Allow up to one minute for the cordless handset and  
telephone base to reset.  
• Clean the cordless handset, charger and telephone base  
charging contacts each month with a pencil eraser or cloth.  
• A blinking CHARGE light is an indication that the battery is not  
connected to the handset or is missing completely. Ensure that  
the battery is installed properly.  
Common cure for electronic equipment.  
If the telephone does not seem to be responding normally, try  
putting the cordless handset in the charger. If it does not fix the  
problem, do the following (in the order listed):  
1. Disconnect the power to the telephone base.  
2. Disconnect the cordless handset battery.  
3. Wait a few minutes.  
4. Connect power to the telephone base.  
5. Completely remove the battery. Replace the battery and place  
the cordless handset into the telephone base or charger.  
6. Wait for the cordless handset to reestablish its connection  
with the telephone base. Allow up to one minute for this to  
take place.  
17  
Appendix  
Maintenance  
Taking care of your telephone  
• Your cordless telephone contains sophisticated electronic parts,  
so you must treat it with care.  
• Avoid rough treatment.  
• Place the handset down gently.  
• Save the original packing materials to protect your telephone if  
you ever need to ship it.  
Avoid water  
• You can damage your telephone if it gets wet. Do not use the  
handset in the rain, or handle it with wet hands. Do not install  
the telephone base near a sink, bathtub or shower.  
Electrical storms  
• Electrical storms can sometimes cause power surges harmful to  
electronic equipment. For your own safety, take caution when  
using electric appliances during storms.  
Cleaning your telephone  
• Your telephone has a durable plastic casing that should retain  
its luster for many years. Clean it only with a soft cloth slightly  
dampened with water or mild soap.  
• Do not use excess water or cleaning solvents of any kind.  
Remember that electrical appliances can cause serious injury if used when you  
are wet or standing in water. If the telephone base should fall into water, DO  
NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND TELEPHONE LINE  
CORDS FROM THE WALL. Then pull the unit out by the unplugged cords.  
18  
 
AImppepndoixrtant safety information  
This symbol is to alert you to important operating or servicing instructions  
that may appear in this user’s manual. Always follow basic safety  
precautions when using this product to reduce the risk of injury, fire, or  
electric shock.  
Safety information  
Read and understand all instructions in the user’s manual. Observe all markings on  
the product.  
Avoid using a telephone during a thunderstorm. There may be a slight chance of  
electric shock from lightning.  
Do not use a telephone in the vicinity of a gas leak. Under certain circumstances, a  
spark may be created when the adapter is plugged into the power outlet, or when  
the handset is replaced in its cradle. This is a common event associated with the  
closing of any electrical circuit. The user should not plug the phone into a power  
outlet, and should not put a charged handset into the cradle, if the phone is located  
in an environment containing concentrations of flammable or flame-supporting  
gases, unless there is adequate ventilation. A spark in such an environment could  
create a fire or explosion. Such environments may include: medical use of oxygen  
without adequate ventilation; industrial gases (cleaning solvents; gasoline vapors;  
etc.); a leak of natural gas; etc.  
Do not use this product near water, or when you are wet. For example, do not use it  
in a wet basement or shower, or next to a swimming pool, bathtub, kitchen sink, or  
laundry tub. Do not use liquids or aerosol sprays for cleaning. If the product comes  
in contact with any liquid, unplug any line or power cord immediately. Do not plug  
the product back in until it has dried thoroughly.  
Install this product in a protected location where no one can trip over any line or  
power cords. Protect cords from damage or abrasion.  
If this product does not operate normally, see the Troubleshooting section on  
pages 10-17 of this user’s manual. If you cannot solve the problem, or if the  
product is damaged, refer to the Limited warranty section pages 25-27. Do not  
open this product except as directed in your user’s manual. Opening the product or  
reassembling it incorrectly may expose you to hazardous voltages or other risks.  
Replace batteries only as described in your user’s manual (pages 6-7). Do not burn  
or puncture batteries — they contain caustic chemicals.  
This power adapter is intended to be correctly oriented in a vertical or floor mount  
position. The prongs are not designed to hold the plug in place if it is plugged into a  
ceiling, under-the-table or cabinet outlet.  
Caution: Use only the power adapter provided with this product. To obtain  
a replacement, visit our website at www.telephones.att.com  
or call 1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.  
19  
 
AImppepndoixrtant safety information  
Especially about cordless telephones  
Privacy: The same features that make a cordless telephone convenient create  
some limitations. Telephone calls are transmitted between the telephone base  
and the handset by radio waves, so there is a possibility that your cordless  
telephone conversations could be intercepted by radio receiving equipment  
within range of the cordless handset. For this reason, you should not think  
of cordless telephone conversations as being as private as those on corded  
telephones.  
Electrical power: The telephone base of this cordless telephone must be  
connected to a working electrical outlet which is not controlled by a wall switch.  
Calls cannot be made from the handset if the telephone base is unplugged,  
switched off or if the electrical power is interrupted.  
Potential TV interference: Some cordless telephones operate at frequencies  
that may cause interference to TVs and VCRs. To minimize or prevent such  
interference, do not place the telephone base of the cordless telephone near  
or on top of a TV or VCR. If interference is experienced, moving the cordless  
telephone farther away from the TV or VCR will often reduce or eliminate the  
interference.  
Rechargeable batteries: This product contains nickel-metal hydride rechargeable  
batteries. Exercise care in handling batteries in order not to create a short  
circuit with conductive material such as rings, bracelets and keys. The battery or  
conductor may overheat and cause harm. Observe proper polarity between the  
battery and the battery charger.  
Nickel-metal hydride rechargeable batteries: Dispose of these batteries in a safe  
manner. Do not burn or puncture. Like other batteries of this type, if burned or  
punctured, they could release caustic material which could cause injury.  
The RBRC™ Seal means that the manufacturer is voluntarily  
participating in an industry program to collect and recycle nickel-  
metal hydride rechargeable batteries when taken out of service  
within the United States. These batteries may be taken to a  
participating local retailer of replacement batteries or recycling  
center. Or you may call 1 (800) 8-BATTERY for locations accepting  
spent Ni-MH batteries.  
20  
 
AImppepndoixrtant safety information  
Precautions for users of implanted cardiac pacemakers  
Cardiac pacemakers (applies only to digital cordless telephones):  
Wireless Technology Research, LLC (WTR), an independent research entity, led  
a multidisciplinary evaluation of the interference between portable wireless  
telephones and implanted cardiac pacemakers. Supported by the U.S. Food and  
Drug Administration, WTR recommends to physicians that:  
Pacemaker patients  
Should keep wireless telephones at least six inches from the pacemaker.  
Should NOT place wireless telephones directly over the pacemaker, such as in a  
breast pocket, when it is turned ON.  
Should use the wireless telephone at the ear opposite the pacemaker.  
WTR’s evaluation did not identify any risk to bystanders with pacemakers from  
other persons using wireless telephones.  
Especially about telephone answering systems  
Two-way recording: This unit does not sound warning beeps to inform the other  
party that the call is being recorded. To ensure that you are in compliance with any  
federal or state regulations regarding recording a telephone call, you should start  
the recording process and then inform the other party that you are recording the  
conversation.  
SAVE THESE INSTRUCTIONS  
21  
 
Appendix  
FCC Part 68 and ACTA  
This equipment complies with Part 68 of the FCC rules and with technical requirements  
adopted by the Administrative Council for Terminal Attachments (ACTA). The label on  
the back or bottom of this equipment contains, among other things, a product identifier  
in the format US:AAAEQ##TXXXX. This identifier must be provided to your telephone  
service provider upon request.  
The plug and jack used to connect this equipment to premises wiring and the  
telephone network must comply with the applicable Part 68 rules and technical  
requirements adopted by ACTA. A compliant telephone cord and modular plug is  
provided with this product. It is designed to be connected to a compatible modular jack  
that is also compliant. An RJ11 jack should normally be used for connecting to a single  
line and an RJ14 jack for two lines. See the installation instructions in the user’s manual.  
The Ringer Equivalence Number (REN) is used to determine how many devices you  
may connect to your telephone line and still have them ring when you are called. The  
REN for this product is encoded as the 6th and 7th characters following the US: in  
the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the  
sum of all RENs should be five (5.0) or less. For more information, please contact your  
telephone service provider.  
This equipment may not be used with Party Lines. If you have specially wired alarm  
dialing equipment connected to your telephone line, ensure the connection of this  
equipment does not disable your alarm equipment. If you have questions about what  
will disable the alarm equipment, consult your telephone service provider or a  
qualified installer.  
If this equipment is malfunctioning, it must be unplugged from the modular jack until  
the problem has been corrected. Repairs to this telephone equipment can only be  
made by the manufacturer or its authorized agents. For repair procedures, follow the  
instructions outlined under the Limited warranty.  
If this equipment is causing harm to the telephone network, the telephone service  
provider may temporarily discontinue your telephone service. The telephone service  
provider is required to notify you before interrupting service. If advance notice is not  
practical, you will be notified as soon as possible. You will be given the opportunity  
to correct the problem and the telephone service provider is required to inform you  
of your right to file a complaint with the FCC. Your telephone service provider may  
make changes in its facilities, equipment, operation, or procedures that could affect the  
proper functioning of this product. The telephone service provider is required to notify  
you if such changes are planned.  
If this product is equipped with a corded or cordless handset, it is hearing aid  
compatible.  
If this product has memory dialing locations, you may choose to store emergency  
telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test  
emergency numbers, please:  
Remain on the line and briefly explain the reason for the call before hanging up.  
Perform such activities in off-peak hours, such as early morning or late evening.  
22  
 
Appendix  
FCC Part 68 and ACTA  
Industry Canada  
Operation is subject to the following two conditions: (1) this device may not cause  
harmful interference, and (2) this device must accept any interference, including  
interference that may cause undesired operation.  
The term ‘’IC:‘’ before the certification/registration number only signifies that the  
Industry Canada technical specifications were met.  
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The  
REN is an indication of the maximum number of devices allowed to be connected  
to a telephone interface. The termination on an interface may consist of any  
combination of devices subject only to the requirement that the sum of the RENs of  
all the devices does not exceed five.  
This product meets the applicable Industry Canada technical specifications.  
23  
Appendix  
FCC Part 15  
This equipment has been tested and found to comply with the requirements for a  
Class B digital device under Part 15 of the Federal Communications Commission  
(FCC) rules. These requirements are intended to provide reasonable protection  
against harmful interference in a residential installation. This equipment generates,  
uses and can radiate radio frequency energy and, if not installed and used  
in accordance with the instructions, may cause harmful interference to radio  
communications. However, there is no guarantee that interference will not occur in  
a particular installation. If this equipment does cause harmful interference to radio  
or television reception, which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference by one or more of the  
following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which  
the receiver is connected.  
Consult the dealer or an experienced radio/TV technician for help.  
Changes or modifications to this equipment not expressly approved by the party  
responsible for compliance could void the user’s authority to operate  
the equipment.  
This device complies with Part 15 of the FCC Rules. Operation is subject to the  
following two conditions: (1) this device may not cause harmful interference, and  
(2) this device must accept any interference received, including interference that  
may cause undesired operation. Privacy of communications may not be ensured  
when using this telephone.  
To ensure safety of users, the FCC has established criteria for the amount of radio  
frequency energy that can be safely absorbed by a user or bystander according  
to the intended usage of the product. This product has been tested and found to  
comply with the FCC criteria. The handset may be safely held against the ear of the  
user. The telephone base shall be installed and used such that parts of the user’s  
body other than the hands are maintained at a distance of approximately 20 cm  
(8 inches) or more.  
This Class B digital apparatus complies with Canadian ICES-003.  
24  
 
Appendix  
Limited warranty  
The AT&T brand is used under license - any repair, replacement or warranty service, and  
all questions about this product should be directed to our website at  
www.telephones.att.com or call 1 (800) 222-3111. In Canada,  
dial 1 (866) 288-4268.  
1. What does this limited warranty cover?  
The manufacturer of this AT&T-branded product warrants to the holder of a valid  
proof of purchase (“CONSUMER” or “you”) that the product and all accessories  
provided in the sales package (“PRODUCT”) are free from defects in material and  
workmanship, pursuant to the following terms and conditions, when installed  
and used normally and in accordance with the PRODUCT operating instructions.  
This limited warranty extends only to the CONSUMER for products purchased and  
used in the United States of America and Canada.  
2. What will be done if the PRODUCT is not free from defects in materials  
and workmanship during the limited warranty period (“materially  
defective PRODUCT”)?  
During the limited warranty period, the manufacturer’s authorized service  
representative will repair or replace at the manufacturer’s option, without charge,  
a materially defective PRODUCT. If the manufacturer repairs the PRODUCT,  
they may use new or refurbished replacement parts. If the manufacturer  
chooses to replace the PRODUCT, they may replace it with a new or refurbished  
PRODUCT of the same or similar design. The manufacturer will retain defective  
parts, modules, or equipment. Repair or replacement of the PRODUCT, at the  
manufacturer’s option, is your exclusive remedy. The manufacturer will return  
repaired or replacement products to you in working condition. You should expect  
the repair or replacement to take approximately 30 days.  
3. How long is the limited warranty period?  
The limited warranty period for the PRODUCT extends for ONE (1) YEAR from the  
date of purchase. If the manufacturer repairs or replaces a materially defective  
PRODUCT under the terms of this limited warranty, this limited warranty also  
applies to repaired or replacement PRODUCT for a period of either (a) 90 days  
from the date the repaired or replacement PRODUCT is shipped to you or (b) the  
time remaining on the original one-year limited warranty; whichever is longer.  
4. What is not covered by this limited warranty?  
This limited warranty does not cover:  
PRODUCT that has been subjected to misuse, accident, shipping or other  
physical damage, improper installation, abnormal operation or handling,  
neglect, inundation, fire, water, or other liquid intrusion; or  
PRODUCT that has been damaged due to repair, alteration, or modification by  
anyone other than an authorized service representative of the manufacturer; or  
25  
 
Appendix  
Limited warranty  
PRODUCT to the extent that the problem experienced is caused by signal  
conditions, network reliability or cable or antenna systems; or  
PRODUCT to the extent that the problem is caused by use with non-AT&T  
accessories; or  
PRODUCT whose warranty/quality stickers, PRODUCT serial number plates or  
electronic serial numbers have been removed, altered or rendered illegible; or  
PRODUCT purchased, used, serviced, or shipped for repair from outside the  
United States of America or Canada, or used for commercial or institutional  
purposes (including but not limited to products used for rental purposes); or  
PRODUCT returned without valid proof of purchase (see item 6 below); or  
Charges for installation or setup, adjustment of customer controls, and  
installation or repair of systems outside the unit.  
5. How do you get warranty service?  
To obtain warranty service, visit www.telephones.att.com or call  
1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.  
NOTE: Before calling for service, please review the user’s manual; a check of the  
PRODUCT’s controls and features may save you a service call.  
Except as provided by applicable law, you assume the risk of loss or damage  
during transit and transportation and are responsible for delivery or handling  
charges incurred in the transport of the PRODUCT(s) to the service location.  
The manufacturer will return repaired or replaced PRODUCT under this limited  
warranty to you. Transportation, delivery or handling charges are prepaid. The  
manufacturer assumes no risk for damage or loss of the PRODUCT in transit.  
If the PRODUCT failure is not covered by this limited warranty, or proof of  
purchase does not meet the terms of this limited warranty, the manufacturer  
will notify you and will request that you authorize the cost of repair prior to any  
further repair activity. You must pay for the cost of repair and return shipping  
costs for the repair of products that are not covered by this limited warranty.  
6. What must you return with the PRODUCT to get warranty service?  
You must:  
Return the entire original package and contents including the PRODUCT to  
the service location along with a description of the malfunction or difficulty;  
and  
Include a “valid proof of purchase” (sales receipt) identifying the PRODUCT  
purchased (PRODUCT model) and the date of purchase or receipt; and  
Provide your name, complete and correct mailing address, and telephone  
number.  
26  
Appendix  
Limited warranty  
7. Other limitations  
This warranty is the complete and exclusive agreement between you and the  
manufacturer of this AT&T branded PRODUCT. It supersedes all other written  
or oral communications related to this PRODUCT. The manufacturer provides  
no other warranties for this PRODUCT. The warranty exclusively describes all of  
the manufacturer’s responsibilities regarding the PRODUCT. There are no other  
express warranties. No one is authorized to make modifications to this limited  
warranty and you should not rely on any such modification.  
State/Provincial Law rights: This warranty gives you specific legal rights, and  
you may also have other rights which vary from state to state or province  
to province.  
Limitations: Implied warranties, including those of fitness for a particular purpose  
and merchantability (an unwritten warranty that the PRODUCT is fit for ordinary  
use) are limited to one year from date of purchase. Some states/provinces  
do not allow limitations on how long an implied warranty lasts, so the above  
limitation may not apply to you. In no event shall the manufacturer be liable for  
any indirect, special, incidental, consequential, or similar damages (including,  
but not limited to lost profits or revenue, inability to use the PRODUCT or other  
associated equipment, the cost of substitute equipment, and claims by third  
parties) resulting from the use of this PRODUCT. Some states/provinces do not  
allow the exclusion or limitation of incidental or consequential damages, so the  
above limitation or exclusion may not apply to you.  
Please retain your original sales receipt as proof of purchase.  
27  
Appendix  
Technical specifications  
RF frequency band  
1921.536MHz - 1928.448MHz  
Channels  
5
Operating temperature  
32°F - 122°F  
0°C - 50°C  
Handset voltage  
2.4VDC - 3.2VDC  
6VAC @ 300mA  
Charger voltage  
(AC adapter output)  
Operation  
Operating time*  
Up to seven hours  
Talk time (cordless handset)  
Talk time (cordless handset speakerphone) Up to five hours  
Standby Up to seven days  
* Operating times vary depending on your actual use and the age of the battery.  
DECT 6.0 digital technology  
The AT&T DECT 6.0 products offer unsurpassed range performance and sound clarity. This  
is achieved through a unique antenna design and advances in noise-filtering technology.  
An independent laboratory has confirmed that AT&T DECT 6.0 products perform up to  
basement, backyard and  
45% better in range competitions. Now calls can be taken in the  
garage with exceptional sound quality.  
Telephone operating range  
This cordless telephone operates within the maximum power allowed by the Federal  
Communications Commission (FCC). Even so, this handset and telephone base can  
communicate over only a certain distance — which can vary with the locations of the  
telephone base and handset, the weather, and the construction of your home or office.  
Redefining long range coverage and clarity  
covers a  
This telephone base comes with an antenna which gives much better clarity and  
longer range than before.  
HD audio  
HD audio improves sound quality by expanding and rebuilding frequencies that are lost with  
traditional phone calls. There is no additional telephone service requirement to use HD audio.  
It is designed to work with standard telephone service. Your system will automatically  
enhance all received sound with HD audio.  
28  
 
© 2011 Advanced American Telephones. All Rights Reserved.  
AT&T and the AT&T logo are trademarks of AT&T Intellectual Property licensed to  
Advanced American Telephones, San Antonio, TX 78219.  
Printed in China. Issue 1 AT&T 01/11.  

GE General Electric Cooktop PP932 User Manual
Frigidaire FGEC3067MB User Manual
Envision Peripherals EN9410e User Manual
Electrolux Libero Line 601610 User Manual
Diamond Multimedia Radeon GX300SE256HM User Manual
Dell Computer Monitor SE178WFP User Manual
Cypress CY7C1294DV18 User Manual
Black Box Computer Hardware VX HDMI IP VRX User Manual
AOC Computer Monitor E943FWS User Manual
AEG COMPETENCE 840E User Manual