PORTABLE CD PLAYER
with AM/FM RADIO
OWNER'S MANUAL
PD5098
PD5098_ib_082003.p65
16
20/8/2003, 16:57
BEFORE WE BEGIN
Thank you… … … … … …
for purchasing this Emerson audio product. The Emerson brand is your assurance
of quality, performance and value, and has been since 1912.
Our engineers have included many useful and convenient features in this product.
Please be sure to read this Owner’s Manual completely to make sure you are
getting the maximum benefit from each feature.
This product was manufactured using the highest qualitycomponents and standards
of workmanship. It was tested by Emerson inspectors and found to be in perfect
working order before it left our factory. However, there is always the chance that
some problem may occur because of rough handling during shipment to the retail
store or to the final consumer.
If, after reading this Manual, you experience any problems with the operation of
this product, please refer to the instructions for obtaining service at the end of this
Manual. Emerson and Emerson retailers are committed to your satisfaction.
Once again, thanks for purchasing this Emerson audio product.
For future reference, record the serial number in the space provided.
Model No.: PD5098
Serial Number :
IMPORTANT NOTES
CLASS 1 LASER PRODUCT
CAUTION
CLASS 1 LASER PRODUCT
INVISIBLE LASER RADIATION
APPAREIL Á LASER DE CLASSE 1
WHEN OPENAND INTERLOCKS
PRODUCTO LASER DE CLASE 1
DEFEATED.
AVOID EXPOSURE TO BEAM
This product contains a low power Laser Device.
2
PD5098_ib_082003.p65
2
20/8/2003, 16:57
• Avoid installing this unit in places • Operate controls and switches as
exposed to direct sunlight or close described in the manual.
to heat radiating appliance such as • Before turning on the power, make
electric heaters, on top of other
stereo equipment that radiates too
much heat, places lacking
certain that the connecting cords,
if any, and power cord are properly
installed.
ventilation or dusty areas, places • Store your CDs in a cool area to
subject to constant vibration and/
or humid or moist areas.
avoid damage from heat.
• When moving the set, be sure to
first disconnect the AC power
cord.
• Do not attempt to clean this unit
with chemical solvents as this
might damage the finish. Use a
clean dry cloth.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequencyenergy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
3
PD5098_ib_082003.p65
3
20/8/2003, 16:57
PREPARATION FOR USE
UNPACKING AND SET-UP
• Carefully remove the unit from the carton and remove all packing material from
the unit.
• Remove any labels or stickers which may be on the front or top of the set, but
do not remove any labels from the back or bottom.
• Press the CD door OPEN button and remove the dummy CD display card from
the CD compartment.
• We suggest that you retain the original carton and packing materials in case it
ever becomes necessary to return your unit for service. This is the only sure
way to protect the unit from damage in transit.
• If you do dispose of the carton and packing materials, please do so properly.
Emerson cares about our environment.
IMPORTANT INFORMATION
• Playing CD’s at higher volume levels increases the battery drain and shortens
the battery life. Try to use AC power whenever it is available.
• You must remove the AC Power Cord from the AC Cord Socket on the back
cabinet in order to operate the unit on batteries.
• We recommend using alkaline batteries for the longest possible life.
• Change the batteries when the output of the unit becomes weak or the sound
becomes distorted. Always change all six (6) batteries at the same time.
• If the unit will be stored and not used for 30 days or more it is recommended to
remove the batteries from the battery compartment to reduce the possibility of
damage from battery leakage or corrosion.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery
compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
(Follow battery manufacturer’s directions.)
4
PD5098_ib_082003.p65
4
20/8/2003, 16:57
LOCATION OF CONTROLS AND INDICATORS
FRONT VIEW
TOP VIEW
1.) AC Socket (At back cabinet).
2.) Speaker.
11.) Telescopic Antenna.
12.) TUNING Control.
3.) Dial Scale.
13.) PLAY/PAUSE
Button.
4.) PHONES Jack.
5.) CD Display.
14.) REV. SKIP/SEARCH
15.) FWD. SKIP/SEARCH
16.) REPEAT Button.
Button.
Button.
6.) CD Door.
7.) Battery Compartment.
(At back cabinet).
17.) PROGRAM Button.
18.) STOP Button.
8.) Carrying Handle.
9.) VOLUME Control.
10.) Function Selector Switch.
(POWER OFF/AM/FM/CD)
19.) CDDoor OPEN Button.
5
PD5098_ib_082003.p65
5
20/8/2003, 16:57
POWER SUPPLY
AC OPERATION
BATTERY OPERATION
Connect the smaller end of the AC power
cord to the AC socket on the back cabinet.
Insert the plug into your 120 volt 60Hz
household AC outlet.
Disconnect the AC power cord from the AC
socket of the unit. Battery power is cut
automatically while the cord the is
connected.
When the volume decreases, or the sound
distorts, replace all of the batteries with new
ones.
AC Outlet
AC Plug
Battery door
CAUTION
To prevent electrical shock, match wide
blade of plug to wide slot and insert fully.
Insert six UM-2 ( size C ) batteries.
ADJUSTING THE SOUND
TO ADJUST THE VOLUME
FOR PRIVATE LISTENING
Plug in headphones (ø3.5 mm stereo mini-
plug) to the PHONES jack on left side panel.
When headphones are plugged in, the
speaker is automatically disconnected.
LISTENING TO THE RADIO
1.) Set to desired Function AM or FM.
2.) Tune in to a station.
TUNING
3.) Adjust the sound.
6
PD5098_ib_082003.p65
6
20/8/2003, 16:57
FOR BETTER RECEPTION
FM
AM
Rotate the unit for best reception.
Extend the telescopic antenna.
AFTER LISTENING
Set the Function switch to ‘POWER OFF’.
COMPACT DISC PLAYBACK
IMPORTANT! The unit should not be carried around during CD playback. If the unit is
subjected to bumps and shocks during playback the disc may skip or stop.
1.) Set Function to CD
2.) Press the CD OPEN button to open the
CD door.
CD
OPEN
3.) Insert a disc with the label side facing
out. Press down near the center hole to
make sure the disc is firmly seated on
the spindle.
4.) Close the CD door by pressing on front
edge of the door.
5.) Press the PLAY/PAUSE
button. Playback will begin on Track 1.
PLAY
PLAY
PAUSE
7
PD5098_ib_082003.p65
7
20/8/2003, 16:57
TO INTERRUPT PLAYBACK
Press the PLAY/PAUSE
button once during playback. Playback stops and the track
display flashes. Press the PLAY/PAUSE
button again to cancel pause and resume
playback at the same point in the track. The track display stops flashing.
TO STOP PLAYBACK
Press the STOP
button and the display
shows the total tracks of the disc.
STOP
NOTE: After pressing the STOP button wait a few seconds for the disc to stop completely
before opening the CD door.
TO SKIP TO THE BEGINNING OF A TRACK
• Press either one of the
direction.
REV /
FWD skip buttons according to the desired skip
• Playback resumes from the selected track.
• When the
FWD button is pressed once during playback, the player advances to the
beginning of the next track.
• When the
REV button is pressed once during playback, the player returns to the
beginning of the track being played. To back up to the beginning of the previous track
press the button twice.
SEARCHING FOR A PASSAGE WITHIN A TRACK
• Keep the
FWD or
REV button pressed during playback, and release the button
as soon as you recognize the desired passage. Normal CD playback will resume from
this point.
SKIP
SEARCH
REV.
FWD.
8
PD5098_ib_082003.p65
8
20/8/2003, 16:57
REPEAT PLAYBACK
This function allows a single track or all tracks on a disc to be played repeatedly.
TO REPEAT THE SAME TRACK
Press the REPEAT button once during
playback. The CD display will indicate
" REPEAT ".
TO REPEAT THE WHOLE DISC
Press the REPEAT button twice until
" REPEAT ALL " displays.
REPEAT
REPEAT
REPEAT ALL
TO CANCEL REPEAT PLAYBACK FUNCTION
Press the REPEAT button again until " REPEAT " or " REPEAT ALL " disappears from the
display.
REPEAT
9
PD5098_ib_082003.p65
9
20/8/2003, 16:57
PROGRAMMED PLAYBACK
Programmed playback enables tracks on a disc to be played in any desired order.
Up to 20 tracks can be programmed.
NOTE : Programming can only be done when the player is in Stop mode.
1.) Press the PROGRAM button. “PROGRAM” indicator flashes in the display.
PROGRAM
PROGRAM
2.) Press the
FWD or
REV button to select the desired track number.
Example: Track 7.
PROGRAM
SKIP
SEARCH
REV.
FWD.
3.) Press PROGRAM button again to memorize the track.
4.) Repeat steps 2 and 3 until all desired tracks are programmed.
5.) Press the PLAY/PAUSE
button to start playback.
PLAY
“PROGRAM " indicator is flashing in the CD display.
PROGRAM
6.) Press STOP button to stop programmed playback. The CD playback stops
but the program remains in the memory.
7.) Press PROGRAM and PLAY/PAUSE
playback.
buttons to resume programmed
8.) To clear the program memory, open the CD door, change to Radio function or
switch the power ‘OFF’.
10
PD5098_ib_082003.p65
10
20/8/2003, 16:57
CARE AND MAINTENANCE
COMPACT DISC CARE
• To remove a disc from its storage case, press down on the center of the case
and lift the disc out, holding it carefully by the edges.
• Treat the disc carefully. Handle the disc only by its edges. Never allow your
fingers to come in contact with the shiny, unprinted side of the disc.
• Do not attach any tape, stickers, etc. to the disc label.
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use detergents
or abrasive cleaners to clean the disc. If necessary, use a CD cleaning kit.
• If a disc skips or gets stuck on a section of the disc, it is probably dirty or
damaged (scratched).
• When cleaning the disc, wipe in straight lines from the center of the disc to the
outer edge of the disc. Never wipe in circular motions.
11
PD5098_ib_082003.p65
11
20/8/2003, 16:57
CLEANING THE UNIT
• To prevent fire or shock hazard, disconnect your unit from theAC power source
when cleaning.
• If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any
wax or polish sprays on the cabinet.
• If the cabinet becomes dirty or smudged with fingerprints it may be cleaned
with a soft cloth slightly dampened with a mild soap and water solution. Never
use abrasive cloths or polishes as these will mar the finish of your unit.
CAUTION:
Never allow any water or other liquids to get inside the unit while cleaning.
12
PD5098_ib_082003.p65
12
20/8/2003, 16:57
TROUBLESHOOTING GUIDE
Should this unit exhibit a problem, check the following before seeking service.
Symptom
Possible Cause
Solution
Radio
Noise or sound
distorted on AM or FM
broadcasts.
Station not tuned properly for Retune the AM or FM
AM or FM.
broadcast station.
FM: Rod antenna is not
extended.
Extend FM Rod antenna.
AM: The bar antenna is not
positioned correctly.
Function switch is not set to
AM or FM.
Reposition the unit until
best reception is obtained.
Set function switch to
AM or FM.
AM or FM no sound.
Volume at minimum.
Increase Volume.
Compact Disc Player
CD Player will not play. Function switch is not set to
CD.
Set unction switch to
CD.
CD is not installed or installed Insert CD with Iabel side
incorrectly.
facing out.
CD skips while playing. Disc is dirty or scratched.
Wipe disc with cloth or use
another disc.
TO FIND THE LOCATION AND PHONE
NUMBER OF YOUR NEAREST SERVICE
CENTER PERMITTED TO PERFORM
WARRANTY...
SERVICE
CALL TOLL FREE: 1-800-695-0098
FOR ADDITIONAL SET-UP OR OPERATINGASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE,PLEASE WRITE TO:
Emerson Radio Corp.
Consumer Affairs Dept.
1901 Diplomat Drive,
Farmers Branch, TX 75234
13
PD5098_ib_082003.p65
13
20/8/2003, 16:57
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts
at an authorized Depot Repair Facility, or replace the product in our discretion.
For repair or replacement, pack your unit in a padded box, enclose your check or
money order payable to Emerson Radio Corp. in the amount of $9.00 (not required
by California residents) to cover shipping and handling costs, and enclose a copy
of your proof of purchase. Send your unit to:
Emerson Radio Corp.
1901 Diplomat Drive.
Farmers Branch, TX 75234.
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTYGIVES YOU SPECIFIC LEGAL RIGHTS, ANDYOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898M
PD5098_ib_082003.p65
14
20/8/2003, 16:57
R
EMERSON
Part No. 16-2864
308-03
Printed in China
PD5098_ib_082003.p65
15
20/8/2003, 16:57
|