Sharp Indoor Furnishings AN 65AG1 User Manual

液晶カラーテレビ用壁掛け金具  
LCD Color TV Wall-Mount Bracket  
Téléviseur couleur LCD et le support de  
montage au mur  
AN-65AG1  
Wandhalter für LCD-Farbfernsehgerät  
Ménsula de montaje el TV color de cristal  
líquido en la pared  
取扱説明書  
OPERATION MANUAL  
MODE D’EMPLOI  
BEDIENUNGSANLEITUNG  
MANUAL DE MANEJO  
・壁用金具取付ネジは同  
梱しておりませんので  
 市販品をお求めください。  
• The wall bracket mounting screws are not in-  
cluded with the product, so please separately  
purchase off-the-shelf screws.  
• Les vis de fixation du support à base ne sont  
pas fournies avec le produit; veuillez donc  
acheter séparément des vis en vente dans le  
commerce.  
• Die Wandhalter-Befestigungsschrauben sind  
nicht im Lieferumfang des Produkts enthalten.  
Besorgen Sie sich daher bitte im Handel  
erhältliche Schrauben.  
適応機種 Used Models / Modéle utilisé /  
Gebrauchtes Modell / Modelo usado /  
• Los tornillos de montaje de ménsula en la pared  
no vienen con el producto, compre los tornillos  
por separado en la tienda.  
LC-6 5 GE1  
 
Please strictly observe the following.  
Special skill is required to install the LCD color  
TV, so please have it installed by a contractor  
specializing in such installation. The customer  
should not attempt to install the TV. Sharp shall  
not be responsible for improper installation or  
any accidents, damage, or injury resulting from  
improper installation.  
To the contractor  
To ensure the safety of the customer, conduct the  
design so that the strength of the installation  
location is sufficiently strong to support the weight of  
the LCD color TV and the wall-mount bracket.  
• Be sure to use two or more people to conduct the  
work.  
• The wall installation screws for the wall-mount  
brackets are not included with the fixtures. Select  
off-the-shelf screws that match the wall.  
Outside dimension drawing  
Base bracket  
(Mark A: At a height at the center of the  
LC-65GE1 screen)  
558  
528  
343  
280  
A
B
18  
518  
220  
220  
Wall-mount bracket  
440  
280  
26  
14  
A
B
460  
35  
440  
468  
478  
Unit: mm  
E-2  
 
Accessories packaged with the TV  
Base bracket: 1  
Wall-mount bracket: 1  
Angle setup bracket: 2  
*Assembly completed  
for perpendicular  
installation.  
Allen wrench: 1  
Screws  
For the angle setup  
bracket  
For installing the wall-  
mount bracket unit  
For fastening the  
wall-mount bracket  
Operation manual  
(This manual)  
M6 length:  
8mm (2 screws)  
M8 length:  
15mm (2 screws)  
M10 length:  
30mm (4 screws) with  
hexagonal sockets  
*The screw notation M6 means the diameter of the threaded part is 6 mm.  
*Please also store the screws that are not used.  
Please use the following  
• Wall installation screws (off-the-shelf) 17  
Be sure to consult the dealership or a qualified contractor when installing the TV.  
• Stand hole covers × 2 (Included with the LCD color TV)  
• A plumb bob made by tying a coin with a hole in it to the end of a string.  
• A pin, such as a thumbtack  
• Cushion, soft cloth, etc.  
Tool (Phillips head screwdriver)  
Installation location  
• LCD color TVs have a viewing angle (range in which the image can be viewed correctly). The  
best viewing position is from directly in front of the screen. Determine the TV installation location  
after taking into consideration the viewing posture, line of sight, and the visual and aural ranges.  
• Sharp shall bear no responsibility for damages, etc., caused by the LCD color TV falling due  
Caution  
to insufficient installation strength or improper installation.  
Weight table (Unit: kg)  
E-3  
 
Wall-Mount Bracket Installation  
Determine the location where the base bracket will be  
installed.  
(1) Use tape or other means to mark the measured positions  
on the wall where the display will be installed. The center  
of the “X” drawn from the four corners of the square marks  
the center of the panel.  
Included part  
1
Base bracket  
(2) Take the coin with the string and align it perpendicular to  
the base bracket.  
Use a pencil, etc., to mark the two screw hole locations.  
Dimension lines  
used as a guide  
Cellophane tape, etc.  
Cellophane tape, etc.  
shaped screw holes  
Wall-mount bracket  
unit installation hooks  
Use a pencil, etc., to  
mark the screw hole  
position on the wall  
behind the bracket.  
String  
Base  
bracket  
outline  
Center  
line  
Position the base  
bracket so that the  
center of it is aligned  
with the string.  
Display  
outline  
Position the base  
bracket so that the  
perpendicular parts  
of it are parallel with  
the string.  
Weight  
1572mm  
*When marking on the wall, use a material that will not leave a permanent mark on  
the wall and get the approval of the customer before beginning the work.  
Tighten the screws  
Temporarily remove the base bracket from the wall and loosely screw in off-the-shelf screws (8  
mm dia. × 2 screws) in the screw hole positions marked on the wall. At this time, the screw  
heads should extend more than 4 mm above the wall so that the base bracket can be hung on  
the screw heads. Hang the base bracket on the installed screws, check to make sure the  
bracket is not sagging to the left or right, and then firmly tighten the screws. Use off-the-shelf  
screws to secure the remaining screw holes (15 screws). (The screw hole diameter is 9 mm.)  
2
Min. 4mm  
Use the weight with the string  
used in Step 1 to make sure  
the bracket is perpendicular.  
E-4  
 
Installing the wall-mount bracket (For Model 65 inch Separate Type)  
• Be sure to use at least two people to perform the wall-mount bracket installation work for the LCD color TV.  
• The installation work must be conducted while the LCD color TV is standing upright, so be careful that it  
Caution  
does not fall over.  
Place the LCD color TV on a strong stand  
1
about 20 to 30 cm high and remove the  
two back terminal covers.  
Two terminal covers,  
top and bottom  
Remove the terminal covers while  
the LCD color TV is standing upright.  
(2 covers top and bottom)  
Remove the 3 fastening screws from both the left and right stands on the back of the  
2
LCD color TV.  
Keep the removed screws (short × 2 screws, long × 4 screws).  
Long screws  
Short screw  
(1) Remove the 2 screws from each of the stand edge covers (total of 4 screws from the  
3
left and right sides).  
Use the removed screws (total of 4 screws) as shown in Step 2 on page 9.  
(2) Remove the stand fastening screws (2 screws each on  
the left and right sides).  
Removing the edge covers reveals  
the stand fastening screws in the  
center of the stands, so remove  
these screws.  
Edge covers  
Edge cover screws  
E-5  
 
Installing the wall-mount bracket (Continued)  
Connect the system cables and power cord to the terminals on the back  
4
of the LCD color TV.  
System cables  
Power cord  
Use the cable holder at the center of the back of the LCD color TV and the cable holders  
holding the speaker cables to connect the system cables.  
5
6
Cable holders  
Surround the system cables.  
(1) Pass through  
the band.  
(2) Pull the band  
forward and  
catch it on  
the hook.  
Included part  
Remove the screw hole plugs (4 plugs) of  
the wall-mount bracket on the back of the  
TV and then screw in the 4 wall-mount  
Allen wrench  
bracket unit screws (hexagonal socket  
screws, M10 length: 30 mm) that are in-  
Hexagonal socket screws  
cluded with the wall-mount bracket unit.  
Wall-mount bracket  
(M10 length: 30 mm)  
Screw hole plugs (4 plugs)  
Mark A  
Included hexagonal socket screws (4 screws)  
Carefully keep the removed screw hole plugs.  
Use an Allen wrench to screw in the included  
hexagonal socket screws into the Mark A holes.  
E-6  
 
Set the angle of the wall-mount bracket  
• Please perform this work before mounting the LCD color TV on the wall.  
Caution  
• When setting the angle of the wall-mount bracket, be careful not to pinch your fingers, etc.  
Remove the perpendicular positioning screws from the wall-mount bracket (2 screws  
1
each on the left and right sides).  
Hole at the very top  
Included part  
Angle setup bracket screws  
M8 length:  
15mm (2 screws)  
Angle setup bracket  
These screws are used for the angle  
setup in Step 2.  
Assemble the included angle setup brackets as shown in the illustration and then use  
2
them to set the TV to the desired angle.  
For the screws, use the included angle setup bracket screws (M8 length: 15 mm × 2 screws)  
and screws removed in Step 1.  
First loosely tighten the 4 screws and then securely tighten them after the angle setup bracket  
is set to the desired position.  
The numbers 5, 10, 15, and 20 at the  
screw holes mean that the higher the  
number, the more the LCD color TV  
slants downward. The angle that can  
be set is limited depending on the  
TV model.  
0
20  
0
2
15  
15  
10  
5
10  
5
E-7  
 
Remove the stands  
• Be sure to use at least 3 people for the work from this point onward.  
Caution  
• Be very careful when holding the LCD color TV at a slant or when lifting it up.  
Lift up the LCD color TV and remove the stand.  
While the stand is being held down, lift up the LCD color TV to remove it from the stand.  
*Remove the LCD color TV from the stand while tipping it backward slightly.  
1
Hold down the stand so that  
it does not move.  
Temporarily place the LCD color TV on a cushion or soft material and install the stand  
2
hole covers that are included with the LCD color TV.  
Hold the LCD color TV at a slant and align the stand hole covers (included with the LCD color  
TV) with the stand insertion locations.  
Use the screws removed during Step 3 on page 6 to attach the stand hole covers and speaker  
cables.  
Stand hole cover  
E-8  
 
Installing the LCD color TV on the wall  
• Be sure to use at least 4 people when installing the LCD color TV to the base bracket.  
Caution  
• Be sure to perform Steps 1 and 2 below. Only performing Step 1 could result in the display falling and  
injuring someone.  
Install the wall-mount bracket attached to the LCD color TV to the base bracket.  
Hang the square holes of the wall-mount bracket on the hooks (see page 5) of the base  
1
bracket unit.  
Check to make sure the hooks are securely inserted into the notches at the top of the slanted  
side of the wall-mount bracket unit.  
Hook  
Notch  
Wall  
Included part  
Fasten the screws in the wall-mount bracket  
2
unit and bottom of the base bracket (Be sure  
Wall-mount bracket fastening screws  
M6 length: 8mm (2 screws)  
to do this).  
Fasten using the included wall-mount bracket  
fastening screws (M6 length: 8 mm × 2 screws).  
E-9  
 
Printed in Japan  
Imprimé au Japon  
Printed on 100% post-consumer recycled paper.  
Imprimé sur 100% de papier recyclé.  
06E  
DSC1  
TINSE1082MPZZ (1)  
 

Sharp Computer Monitor LL T17D4 User Manual
Sharp Flat Panel Television LC 26D4U User Manual
Snapper Lawn Mower 1690583 User Manual
Snapper Snow Blower Snower Thrower User Manual
Sony Camera Lens TW25 User Manual
Sony DVD Player S9000ES User Manual
Spectra Laser Level GL622 User Manual
SPX Cooling Technologies Humidifier SS NC 08A User Manual
Stiga Lawn Mower 13 2570 13 User Manual
Sunrise Global Outdoor Kitchen Island Cable Explorer TDR Module User Manual